What are your beliefs about A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't exactly rocket science, but it does call for strong plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old bathtub is readily obtainable, the job can move quickly; if you have to open a wall surface to remove the old tub and place the new bathtub, the job is much harder. In either case, the task is within a house handyman's abilities, although you will certainly need an assistant to vacate the old tub as well as set in the new one. See to it you have certified yourself for the job as well as are comfortable trying it. Instead of working with a specialist to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This short article will certainly assist you mount a new tub in your bathroom if you have currently gotten a brand-new tub as well as do not require to change the arrangement of your previous water pipes.
Your devices as well as material list must comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you need to do is detach the water system. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing faucets can be fairly troublesome as a result of the restricted accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. When the supply pipelines have been eliminated, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Before proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in area between the tap as well as the sink. Safeguard the faucet in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The former type needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using the two wooden boards under its feet, position the bathtub in the called for setting. The wood boards are practical in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the furthest versatile tap port to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water system and also check all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub and additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, deal with the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub must wait up until the bath tub has been used at the very least once as this will resolve it into its last placement.
Preparing for the Setup
To start with, the supporting framework supplied with the bathroom must be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets unit to prevent pressure on the bath tub.
Fit the versatile faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must now prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to crack a stiff seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, bring about problems with wetness as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components and installations. They are offered in tubes and also cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to permit the activity experienced when the bathtub is in use. The sealant can split relatively very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that blog post about How to Install a Bathtub when scouting around the web. Sharing is nice. You won't know, you may very well be helping someone out. Kudos for your time. Don't forget to pay a visit to our blog back soon.
Pro assistance? Dial.